Quick Answer
Move the pointer into the box, then press each mouse button, scroll the wheel up and down and double-click. Each action lights up and is counted. Move the mouse quickly in circles to see the highest rate of movement events. Press Reset counts to start again.
Embed this calculator
Adjust the size if needed, then copy the code below into your page or blog. The calculator will load in an iframe and stay updated automatically.
Table of Contents
- Mouse Tester
- Quick Answer
- Related Calculators
- How This Mouse Tester Works
- How to Use the Mouse Tester
- How the Test Reads Your Mouse
- Key Terms
- Worked Example
- Real-Life Examples
- Mouse Tester vs Click Speed Test
- Button Numbers
- Tips for Testing a Mouse
- Common Mistakes to Avoid
- Frequently Asked Questions
- References & Sources
How This Mouse Tester Works
A mouse can fail in small ways: a button that sometimes does not register, a scroll wheel that jumps, or a switch that double-clicks by itself. This tester shows you what the browser actually receives from your mouse, so you can see a fault instead of guessing.
Move into the test box and press every button. The matching badge lights up and the count goes up. Scroll the wheel to count steps up and down, and double-click to check that your clicks are recorded as double clicks. A live line shows how many movement events your browser is getting each second.
Features:
- All five buttons: left, middle, right, back and forward, with a count for each.
- Wheel test: counts scroll steps up and down.
- Double-click check: finds a switch that clicks twice when you press once.
- Polling rate estimate: shows how many movement events per second the browser sees.
How to Use the Mouse Tester
- Move the pointer into the test box.
- Press the left, middle, right, back and forward buttons.
- Scroll the wheel up and down, and double-click.
- Move the mouse quickly in circles to see the highest movement rate.
- Press Reset counts to run the test again.
How the Test Reads Your Mouse
- Buttons: the browser numbers each button: 0 is the main (usually left) button, 1 is the wheel or middle button, 2 is the secondary (usually right) button, 3 is the back button and 4 is the forward button. Left-handed setups can swap these, so a left-handed option swaps left and right for you.
- Wheel: each wheel event has a vertical change that is negative when you scroll up and positive when you scroll down. The tester counts the events in each direction.
- Double clicks: counted when the browser reports two quick clicks in the same place.
- Movement events per second: the browser merges many small mouse movements into a single event. This tool counts the merged movements too, where the browser lets it, then adds up how many happened in the last second.
- Highest rate: the biggest per-second count seen while you kept moving for at least about half a second.
Key Terms
- Polling rate: how many times per second a mouse reports its position, in Hz.
- Double click fault: a switch that registers two clicks for one press.
- Scroll wheel: the wheel between the buttons, used to scroll.
- Pointer events: browser events that report mouse, touch and pen input.
Worked Example
- You click the left button 10 times and the counter shows 10, so the left button registers every press.
- You move the mouse in fast circles and the highest rate shows 500 per second. Your mouse is probably set to a 500 Hz or 1,000 Hz polling rate, but the number is only an estimate.
- You press the right button once and the count shows 2. That is a sign of a worn switch that registers twice.
- You scroll the wheel up 5 notches and see 5 steps up and 0 down, which is correct.
Real-Life Examples
- Checking a second-hand mouse: make sure all 5 buttons and the wheel work before you buy.
- Double-click faults: press the left button 20 times slowly and see if the count goes above 20.
- Gaming setup: check that the side buttons you have mapped actually register.
- Troubleshooting: compare two mice, or two USB ports, to find a flaky connection.
Mouse Tester vs Click Speed Test
- Mouse tester: checks that every button, the wheel and the movement work. Best for finding faults.
- Click speed test (CPS): counts how many clicks you can do in a few seconds. Best for measuring your own speed.
- Together: test the mouse first, then use the CPS test to measure speed.
Button Numbers
| Number | Button | Usually |
|---|---|---|
| 0 | Main button | Left button |
| 1 | Auxiliary button | Wheel press or middle button |
| 2 | Secondary button | Right button |
| 3 | Fourth button | Back |
| 4 | Fifth button | Forward |
Tips for Testing a Mouse
- Click slowly and fast: a failing switch often misses fast clicks or doubles slow ones.
- Test the wheel both ways: a dirty wheel sensor can count a step in the wrong direction.
- Move quickly for polling rate: slow movement gives low numbers that say nothing about your mouse.
- Try another USB port: a loose or shared port can cause skips.
- Clean the sensor and mouse pad: dust and shiny surfaces cause jumpy pointers.
Common Mistakes to Avoid
- Moving the mouse outside the box. The test only counts actions inside the box.
- Reading the polling rate as exact. It depends on the browser and how fast you move, so use it as a guide.
- Expecting side buttons on a basic mouse. Many mice have only three buttons and a wheel.
- Forgetting left-handed swaps. If your mouse is set to left-handed, use the left-handed layout so labels match.
- Blaming the mouse for a slow computer. Test on a quiet system before you decide.
Frequently Asked Questions
Move into the box, then press each button and scroll the wheel.
Yes, with no download and no sign-up.
No. Everything stays in your browser.
Press a button 20 times slowly. If the count goes above 20, the switch is registering extra clicks.
How many times per second the mouse reports its position, such as 125, 500 or 1,000 Hz.
Move the mouse quickly in circles, and remember it is only an estimate.
Your mouse may not have one, or your system may use it for something else.
Yes, but a trackpad has no middle, back or forward buttons.
Yes. Choose the left-handed layout so left and right match your settings.
The box captures the wheel so you can count steps. Scroll outside it to move the page.
It reads touch too, but it is made for a mouse.
The test box turns it off so right-clicks are counted instead.
Try cleaning it, another USB port or another computer, then consider a replacement.
No. Polling rate is updates per second, and DPI is how far the pointer moves for each inch of movement.
References & Sources
| Source | Used For | Link |
|---|---|---|
| MDN, MouseEvent.button | Button numbers: 0 main, 1 auxiliary, 2 secondary, 3 back, 4 forward, and left-handed layouts. | https://developer.mozilla.org/en-US/docs/Web/API/MouseEvent/button |
| MDN, PointerEvent.getCoalescedEvents() | How browsers merge many pointer updates into one movement event, and how to read them. | https://developer.mozilla.org/en-US/docs/Web/API/PointerEvent/getCoalescedEvents |