Quick Answer
Turn your volume down a little, then press Left, Both or Right. You should hear the sound only from the side you picked. If the left sound comes from the right, your headphones are on backwards or your cables are swapped. Use Sweep to check the full range from deep bass to high treble, and Noise to listen for rattles or crackles.
Embed this calculator
Adjust the size if needed, then copy the code below into your page or blog. The calculator will load in an iframe and stay updated automatically.
Table of Contents
- Sound Test
- Quick Answer
- Related Calculators
- How This Sound Test Works
- How to Use the Sound Test
- How the Test Sounds Are Made
- Key Terms
- Worked Example
- Real-Life Examples
- Sound Test vs Tone Generator
- Frequency Guide
- Fixing Common Sound Problems
- Common Mistakes to Avoid
- Frequently Asked Questions
- References & Sources
How This Sound Test Works
When speakers or headphones sound wrong, it helps to test them with known sounds. This page plays test sounds in the left channel, the right channel or both, so you can check that each side works, that stereo is the right way round, and that the sound is clean across the whole range.
What you can test:
- Left and right: each side plays on its own.
- Balance: Both should sound centered, not louder on one side.
- Frequency range: a sweep from 20 Hz (deep bass) to 20,000 Hz (very high treble).
- Bass: a slow sweep from 40 Hz to 120 Hz for subwoofers and bass speakers.
- Rattles and crackles: noise covers every frequency at once, so faults stand out.
How to Use the Sound Test
- Turn your device volume down to a comfortable level.
- Press Left, Both or Right.
- Listen for the sound on the matching side only.
- Pick Sweep, Bass or Noise and press Play sound to test range and clarity.
- Press Stop at any time.
How the Test Sounds Are Made
- Web Audio: every sound is generated live by your browser, so it plays without downloading files.
- Stereo panner: a pan value of −1 sends sound fully left, +1 fully right and 0 to both sides equally.
- Chime: three sine notes, C5 (523 Hz), E5 (659 Hz) and G5 (784 Hz).
- Sweep: a sine wave that glides on an exponential curve, so each octave gets the same time. 20 Hz to 20,000 Hz is about 10 octaves in 10 seconds, so about 1 second per octave.
- Noise: random values at every sample, which contain all frequencies at similar strength (white noise).
Key Terms
- Stereo: sound with separate left and right channels.
- Hz (hertz): vibrations per second; higher numbers are higher pitches.
- Sweep: a tone that slides smoothly from low to high.
- White noise: a hiss that contains all frequencies at similar levels.
Worked Example
Your new headphones seem to have the sound the wrong way round in games.
- Press Left. The sound comes from your right ear, so the sides are swapped.
- Check the L and R marks on the headphones and turn them round.
- Press Left again: now it is in your left ear. Press Right to confirm.
- Run the Sweep. You hear it from a low hum to a high whistle, but it fades out near the end. That is normal: many adults cannot hear above about 15,000 Hz.
Real-Life Examples
- New headphones: check that left is left before a game or video call.
- Home cinema: run the bass sweep from 40 Hz to 120 Hz to hear if the subwoofer buzzes at one spot.
- Car stereo: play Left, then right on repeat to check each door speaker.
- Hearing check for fun: watch the sweep and notice where it fades; at 1 second per octave, fading at 8 seconds means about 5,000 Hz.
Sound Test vs Tone Generator
- Sound test: quick checks of left, right, balance and range for speakers and headphones.
- Tone generator: plays one exact frequency for as long as you like, for tuning or experiments. Use our Tone Generator for that.
- Mic test: checks the input side (your microphone) instead of the output.
Frequency Guide
| Range | Frequencies | Examples |
|---|---|---|
| Sub-bass | 20 to 60 Hz | Rumble felt more than heard |
| Bass | 60 to 250 Hz | Bass guitar, kick drum |
| Midrange | 250 to 4,000 Hz | Voices, most instruments |
| Treble | 4,000 to 20,000 Hz | Cymbals, the s in speech |
Fixing Common Sound Problems
- No sound at all: check the volume, the mute button and which output device your computer or phone is using.
- Only one side works: try another cable or port, and check the balance setting in your sound settings.
- Left and right swapped: swap the speakers or wear the headphones the other way round.
- Crackling: often a loose plug, a damaged cable or a speaker played too loud.
- No deep bass: small laptop and phone speakers usually cannot play below about 100 Hz.
- Bluetooth delay: wireless headphones can lag, so sound may start slightly after you press the button.
Common Mistakes to Avoid
- Starting too loud. Turn the volume down first, especially with headphones.
- Testing the wrong device. Check which output your system is using.
- Blaming the speaker for missing bass. Small speakers cannot play very low notes.
- Long high tones at high volume. They are tiring and can harm hearing.
- Forgetting Bluetooth lag. A short delay is normal on wireless headphones.
Frequently Asked Questions
Press Left, Both and Right and listen for the sound on the matching side.
Press Left. If you hear it on the right, the sides are swapped.
Very low notes near 20 Hz are hard to hear and most small speakers cannot play them.
Most adults cannot hear above about 15,000 to 17,000 Hz, and many speakers roll off there too.
Yes at a sensible volume. Start low and turn it up slowly.
Yes. There may be a short delay.
No. It only plays sound.
Check that the phone is not on silent; some phones mute web audio in silent mode.
Yes. Use the Bass check and listen for buzzing or rattling.
Three notes: C, E and G, which make a major chord.
Choose Steady tone and enter any frequency from 20 to 20,000 Hz.
It plays all frequencies at once, so rattles, crackles and a weak side are easy to notice.
Yes. Choose Left, then right and press Play sound. Press Stop to end it.
No. It tests stereo left and right only.
References & Sources
| Source | Used For | Link |
|---|---|---|
| MDN Web Docs, StereoPannerNode | How the browser pans sound to the left or right. | https://developer.mozilla.org/en-US/docs/Web/API/StereoPannerNode |
| MDN Web Docs, OscillatorNode | How the test tones and sweeps are generated. | https://developer.mozilla.org/en-US/docs/Web/API/OscillatorNode |
| Wikipedia, Hearing range | The human hearing range of about 20 Hz to 20,000 Hz and how it changes with age. | https://en.wikipedia.org/wiki/Hearing_range |